Conductor Electric Corp.

03/03/2026

02/22/2026

New construction, single family home 4br, 2.5 bath.

Key notes:
• Kick plates/ nail guards used where the wire is less than 1-1/4" to the face of the stud.
• Dedicated 20a GFI in garage - Mandatory!
• GFI protection for bathroom, kitchen & basement receptacles.
• 4k spectrum LED
• ARC fault protection for living areas.
• Weather proof GFI by outdoor HVAC equipment as well as in the front and rear of house.
• Attic lighting & power for HVAC service.
• 200a main service

12/22/2025

Each product is built with a purpose— to create a better, more accessible world. The SkyPlug and Receptacle are the foundation of the revolutionary platform.

I found some of these products for sale at Home Depot and it looks like the outlet and light kit will run you about 70 bucks however, the price can vary. There are some upgraded and additional options to choose from.

Imagine delivering a completed electrical system, for a new house, only having installed the skyplug for each light location.....the homeowner can follow up with light fixtures themselves just plugging them in. No more waiting for final inspection because because of fixture delays or replacements.

Keep in mind electricians - a light must be still be installed in bathrooms & kitchens at the least !

09/14/2025

This is a nice five port deck box with a built-in ground bar. Perfect for pools with four lights.

This particular installation was using pentair low voltage micro brights. These lights are nice because they come pre-wired and sealed with a long cord that reaches the deck box.

Overall a safer choice because the lighting is only 12 volts.

One downside is the need for a transformer which can add around a hundred bucks + to buy and additional work for installing.

03/18/2025

This all electric 120 AMP tankless hot water heater can fit inside a briefcase. It can also provide hot water for two shower heads @1.5 GPM/ ea and one sink at .5 GPM simultaneously. It's acceptable for the North where ground water supply temps can be pretty cold.
I think it's a little strange having three 8/2 supply lines to feed it. This is also a bit clunky in the panel taking up six breaker spaces. Maybe this will be improved upon as this technology becomes more widely used. I was a little concerned about using it at first, however it's proving itself reliable for at least two homes this past winter. So happy that it's keeping up to it's claims! Thanks .de for such a great and well made product. Keep up the good work 😀

06/11/2024

5/8" GND ROD -

This ground rod gets driven into the ground 8' deep. Two of them are required where a PVC water main exists.

I wanted to show the use of anti-oxidant compound. It's a wee messy but prevents oxidation pretty well.

Another good product to prevent oxidation is . The difference is no conductivity and it dries clean to touch.

03/30/2024

There are two different spectrums of lighting here. It's hard to notice how warm the pendants actually are @ 2500k, while the black pipe lights are a shockingly bright 6500k.

I was initially afraid to mix these two spectrums as they're basically extreme opposites, however I really like having the option.

The daylight spectrum will cut the wam light righ out of sight, leaving a crisp and bright lighting for cleaning or working. The warm light is great for early morning or in the evening for relaxing.

Although this may be controversial to most lighting plans, I would say don't be afraid to mix the two spectrums assuming you have independent control of the two.

03/29/2024

This is a low voltage fixture starting at the junction point on the ceiling.

120v supplies a step down transformer and from there it's low voltage to the 2 prong G9 LED bulbs.

03/29/2024

Loose and improperly connected terminals can lead to arcing. Arcing leads to fire 🔥

Here are a few essential things that must be done when connecting and outlet....

1) Wrap the hook so it sits fully underneath the screw.
2) The direction of the hook must be as shown. When you tighten the screw it also closes the hook.
3) Check the torque by using a flathead screwdriver. Proper torque is sometimes hard to tell when using a screw gun. Especially if you are not very familiar with the tool.

03/27/2024