No-Dig Depot

No-Dig Depot Specialist equipment, materials and consumables for pipe reliners, plumbers and drainage professionals.

Quality no-dig gear, practical support and reliable supply across Australia.

Not every retrieval job should end with a shovel. The Boldan PipeCatcher is an air-driven tool designed to retrieve drop...
07/08/2026

Not every retrieval job should end with a shovel.

The Boldan PipeCatcher is an air-driven tool designed to retrieve dropped tools and remove rocks, roots and other obstructions from inside a pipe, helping avoid unnecessary excavation and demolition.

Rotate the push hose to position it, then use the air valve to close and release the claws. It comes with three claw sets with the smallest suitable for DN70 / 3-inch pipes and bends of up to 45 degrees.

It may be compact, but with a lifting capacity of more than 100 kg, it’s damn capable. Five and ten-metre push hoses are available separately and can be connected when extra reach is needed.

Made in Finland, used around the world by plumbers, reliners and maintenance crews dealing with problems that are difficult to reach and far too costly to dig up.

This is essential gear. On the right job, it could save you thousands.

The MidiCoater+ handles pipe cleaning, spray coating and brush coating from the one unit. There’s a fair bit packed into...
24/07/2026

The MidiCoater+ handles pipe cleaning, spray coating and brush coating from the one unit. There’s a fair bit packed into it.

The dual-cartridge setup means less stopping to swap material during a coating run, while the heated high-flow hoses allow contractors to work across pipes from DN32 to DN160 and reach lengths of up to 30 metres.

Spray coating gives a smoother, more consistent finish. Brush coating is there for the tighter bends and deeper joints where spraying alone won’t quite get it done.

For reliners already offering pipe coating, or looking to bring it into the business, it’s a practical system without a pile of separate equipment.

Speak with the No-Dig Depot team for pricing, availability and technical details.

Relining jobs don’t always go exactly as planned.The pipe can be worse than the camera suggested. Access is tighter than...
16/07/2026

Relining jobs don’t always go exactly as planned.

The pipe can be worse than the camera suggested. Access is tighter than expected. A product behaves differently on site than it did in training (usually when there’s no time to spare).

That’s where the supplier behind the gear starts to matter.

No-Dig Depot works with plumbers who are already relining, and those looking to add it properly to their business. Equipment, materials and training are part of it. Being able to call someone who understands the system and the job is the other part.

Because when the liner is mixed, the customer is waiting and something doesn’t look right, a product catalogue isn’t much help.

Practical gear. Straight advice. Support from people who know relining.

Buying relining gear is one thing.Knowing it is the right gear for the job is another.A lot can get expensive once a job...
09/07/2026

Buying relining gear is one thing.

Knowing it is the right gear for the job is another.

A lot can get expensive once a job is already underway. The wrong setup. The wrong material choice. No one picking up the phone when something does not look quite right on site.

That is where a small issue can turn into lost days and a much bigger cost.

No-Dig Depot supplies relining equipment and materials, but the support matters just as much.

Our team knows relining. We help plumbers with product selection, setup, training and practical job support, so they are not left working it out under pressure.

Because once the liner is in, guessing is not much of a plan.

Drop us a DM to learn more.

07/07/2026

UV cure is coming to No Dig Depot.

For the right relining jobs, it gives plumbers a faster way to cure liners without overcomplicating the setup.

Cures in minutes. Compact and lightweight. Used with WaterMark products.

It’s a practical bit of kit, especially when the job needs speed, consistency and a safer curing process on site.

More on this next month.

02/07/2026

Good session with Dylan and the team from Inline Plumbing Group.

The focus was relining with the PIP Packer system and the Boldan junction repair system.

They’re building out their relining capabilities and investing in the gear to take on more of this work properly. Not just having the equipment sitting in the van, but knowing how to use it on real jobs.

That’s where the training side matters.

No Dig Depot supports plumbers with the tools, setup and practical training to help them get moving with confidence.

EOFY is probably the right time to look at Renssi gear if it’s already been on your radar.For a limited time, No-Dig Dep...
17/06/2026

EOFY is probably the right time to look at Renssi gear if it’s already been on your radar.

For a limited time, No-Dig Depot is including selected bonus items with Renssi inversion drums and milling machines.

With any Renssi drum purchase, including the 400S, 600S, 800S or 800XL, you’ll receive 3 x free Storz nozzles.

The usual drum sizes we stock are the 400S and 800S, so they’re typically the quickest options to check availability on.

For milling machines, the offer applies to both the RCX-10 and RCX-12.

The RCX-10 comes with a free Renssi Chain Kit and Sanding Kit, valued at over $4,000.

The RCX-12 comes with a free Renssi Cutter Kit, valued at over $5,000.

Good gear. Good timing.

Get in touch with No-Dig Depot to check availability before EOFY.

EOFY clearance is now on for Willkat Silicate Resin Kits.Save over 25% while stock is available.Normally $826.50 + GSTNo...
11/06/2026

EOFY clearance is now on for Willkat Silicate Resin Kits.

Save over 25% while stock is available.

Normally $826.50 + GST
Now $594 + GST

You can also save a bit more when you bundle.

Get an extra 10% off rolls of ECR Fibreglass Mat when bundled with a resin kit.

Good opportunity to stock up before EOFY, especially if you’re already using silicate resin on smaller relining jobs.

Contact No-Dig Depot to check availability.

30/03/2026

Built for real work, ready when you are. 15% off Boldan Equipment from No-Dig Depot, for a limited time.

Call or message now to secure yours.

Address

Unit 10B/30-32 Perry Street
Matraville, NSW
2036

Opening Hours

Monday 9am - 5pm
Tuesday 9am - 5pm
Wednesday 9am - 5pm
Thursday 9am - 5pm
Friday 9am - 5pm
Saturday 9am - 12pm

Website

Alerts

Be the first to know and let us send you an email when No-Dig Depot posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to No-Dig Depot:

Shortcuts

Share

Category