BWB Engineering

BWB Engineering Repair instead of replace!

Electrical and Mechanical Engineering
Covering AC-DC
Covering Petrol and Diesel
JLR and Ford trained

If it should run smooth and it doesnt
If it needs TLC/Servicing
If it needs a Full Rebuild

Then we are here to help.

22/08/2026

“Ultra light Aircraft”
“No licence needed”

🧐🧐🧐🧐🧐🧐🧐🧐🧐🧐🧐🧐🧐

Time to find a few big motors, make a big battery and fabricate a lightweight frame! 🤓🤓🤓🤓🤓🤓

In the UK, ultralight pilots must complete training with a qualified instructor, although there are no specific licensing requirements for flying ultralights. Training typically includes both theoretical knowledge and practical flight experience to ensure safety and proficiency.
eaa.org
caa.co.uk
Training Requirements for Ultralight Pilots in the UK
General Overview
In the UK, ultralight pilots are not required to hold a specific license to fly ultralight aircraft. However, they must complete training with a qualified instructor to ensure safety and proficiency.
Training Components
The training for ultralight pilots typically includes:
Theoretical Knowledge: Understanding the principles of flight, navigation, meteorology, and air law.
Practical Flight Experience: Hands-on training with an instructor, which may involve:
Dual flying sessions
Solo flying under supervision
Key Points
No Licensing Requirement: Unlike other types of aircraft, ultralight pilots do not need a formal license.
Safety Emphasis: While formal licensing is not required, training is crucial for safe operation.
Instructor Qualification: Training must be conducted by a qualified instructor to ensure that pilots are adequately prepared for flying.
This structure helps maintain safety standards in ultralight aviation while allowing for greater accessibility to flying.

22/08/2026

For 1 tonne of copper out of the earth, you have to mine 200 tonne of soil.
👀👀👀👀👀👀👀
No wonder it’s climbing above £10kg

Even EPNS is doing £15/16 a kg

Recycle!







Little mobile job today. Remove turbo, and take it to be reconditioned.Main shaft has grooves in from contamination 🙈 Lo...
21/08/2026

Little mobile job today.
Remove turbo, and take it to be reconditioned.

Main shaft has grooves in from contamination 🙈

Long weekend it is then:







19/08/2026







Have to take my hat off to Ford this time around! Definitely easier than the 2017 Mk8 transit. They’ve given me a functi...
19/08/2026

Have to take my hat off to Ford this time around!
Definitely easier than the 2017 Mk8 transit.

They’ve given me a functional connection at the rear of the van, complete with a Ford blank on, on the 2019 onwards shape, 2022 model for today’s antics…

Managed to find a molex plug for the Ford connection. 🥳🥳🥳

So time to connect the ends up in the correct order 👀👀👀

Prove all the pre-made connections and continuity on the cables.

Also deciphering the cryptic instructions and wiring layouts 👀👀👀👀
Probably would have been best buying blank outlets and wiring them from starch 🤷‍♂️ I’m given what I’m given ☺️

Those Dirty horrible Scotch locks 🤢🤮🤢 will all be going in the blue recycling bin! Word of advise, don’t ever use these if you plan on keeping what you’ve just wired 🥴🥴🥴🥴🥴

Bought the 7 pin, and a 13 pin, but I’m inclined to keep it simpler, and use the 13 pin, and have an adapter if an older trailer is used, not common today the old 7 pins….

That’s a shame as it’s only 1/2 as many wires to connect! 🤣🤣🤣🤣

Been rained off, so hiding indoors

☔️ 🌧️ ☔️







VVT left the chat! This was definitely on high revs when this one died 🫣🫣🫣🫣🫣 Fired the chain through the chain over, abs...
18/08/2026

VVT left the chat!
This was definitely on high revs when this one died 🫣🫣🫣🫣🫣
Fired the chain through the chain over, absolutely destroyed the cover.
7x smashed followers too, so actually not too bad….







17/08/2026





😍😍😍😍😍😍😍😍😍 Proper Disco 💪💪💪💪 TD5 not quite running right…. Injectors removed and sent off for testing…. New injector bolt...
17/08/2026

😍😍😍😍😍😍😍😍😍
Proper Disco 💪💪💪💪

TD5 not quite running right….
Injectors removed and sent off for testing….
New injector bolts and copper seals to be ordered, plus a little hole cleaning.

She’s had a new filter, lift pump, pressure sensor o ring…. And that didn’t fix her.

So it’s my turn now 😎😎😎

Process of elimination…..
without firing the “parts cannon” at it









I wonder why the new cars break? How did anyone think having a double chain was a bad idea (other then for future sales)...
17/08/2026

I wonder why the new cars break?

How did anyone think having a double chain was a bad idea (other then for future sales)
To then decide, I know let’s make it weaker, we will convince them it’s all down to emissions and drag, we’ll tell them to stop using 10-40w oil and use 0-20/0-30w too.

We can guarantee the engines will die within the 100/120k mark then. 👌🫣

Can’t beat an old school diesel engine for utter reliability and bullet proof!

They do need a little love every now and then, but atleast it’s not a full rebuild 👀👀👀👀👀👀








Address

New Lane Pace
Banks
PR98EZ

Website

Alerts

Be the first to know and let us send you an email when BWB Engineering posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to BWB Engineering:

Shortcuts

Share