Aguyy 2.1

Aguyy 2.1 Hi Crush😍
Aguyy?

Ayaw ko hindi pato Tuli ey😅
07/08/2026

Ayaw ko hindi pato Tuli ey😅

07/08/2026

All done

06/08/2026

Sarap maligo

04/08/2026

Catv & telephone pipe lay-out


Facebook

03/08/2026

Ayun

Nagseselos kahit na walang level
🥺🥺🥺

19/07/2026

Electrical Experience before NCll

Ilan nga ba ang regular height ng panel🤔Here are the standard heights based on Philippine Electrical Code (PEC) and comm...
18/07/2026

Ilan nga ba ang regular height ng panel🤔

Here are the standard heights based on Philippine Electrical Code (PEC) and common local practice:

📌 Legal Requirement (PEC)

- Max height: The highest breaker handle must be ≤ 1.98 m (78 in) above finished floor.
- Min height: No strict PEC rule, but usually ≥ 0.30 m (12 in) from bottom to floor for safety.

📏 Regular / Recommended Mounting Heights

Reference Point Typical Height Notes
Center of panel 1.40 m – 1.50 m Most common; easy eye-level access
Top of panel 1.80 m Often specified in public/commercial projects[__LINK_ICON]
Bottom of panel 1.20 m – 1.30 m For smaller residential panels

✅ Quick Guide

- Residential: Usually set so center is ~1.40 m or top at 1.80 m.
- Commercial/Institutional: Often top at 1.80 m above finished floor .
- Always: Ensure highest breaker handle ≤ 1.98 m.

All measurements are taken from Finished Floor Level (FFL).

Regular height for submeterA sub-meter (electricity) should be installed at eye level, typically between 1.5 meters to 1...
17/07/2026

Regular height for submeter

A sub-meter (electricity) should be installed at eye level, typically between 1.5 meters to 1.8 meters (59 to 71 inches) from the finished floor to the center of the meter. This specific height allows for easy reading, recording, and routine inspection without excessive bending or reaching.

Pangunahing Sanhi ng PagkasunogLoose Contact (Maluwag na Koneksyon): Ang mga maluwag na turnilyo o terminal ay lumilikha...
17/07/2026

Pangunahing Sanhi ng Pagkasunog

Loose Contact (Maluwag na Koneksyon):

Ang mga maluwag na turnilyo o terminal ay lumilikha ng mataas na resistance. Kapag dumaan ang kuryente, nagdudulot ito ng labis na init (arcing) na maaaring mag-apoy sa mga materyales sa paligid.

Overloading:

Ang paggamit ng mga appliances na lumalagpas sa kapasidad ng circuit breaker o panel board ay nagpapainit sa mga kable nang higit sa kanilang normal na limitasyon.

Undersized Wires:

Ang paggamit ng manipis na kable para sa mga mabibigat na appliances ay nagdudulot ng sobrang init dahil hindi nito kayang daloyn ang kailangang kuryente.

Short Circuit:

Ang pagdikit ng dalawang live wire o ng live wire sa neutral/ground dahil sa lumang insulation ay nagdudulot ng biglaang pagtaas ng init na maaaring magsunog sa board.

17/07/2026

Daming dahilan kung bakit nasunog to!
Karamihan akala nila at akala ko rin ang dahilan ng pagkasunog ng mga panel or wiring's

Lost Connection
Overload
Undersized yung wire na ginamit
Or iba pa

Kung sasabihin kung nabas lang ito ng tubig maniwala ba katao🤦‍♂️

Address

Tigum, Aklan
Buruanga
5609

Website

Alerts

Be the first to know and let us send you an email when Aguyy 2.1 posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category