Top Notch Electric, LLC

Top Notch Electric, LLC Licensed and Insured Electrical Contractor
Located in Humphrey, NE
Serving the Northeast Nebraska area. Give us a call for an estimate.

Residential, Commercial, and Agricultural

New construction, remodels, updates, and service calls.

A flagpole fell over and snapped off at a post office. We had the privilege to put up a new one.
01/08/2026

A flagpole fell over and snapped off at a post office. We had the privilege to put up a new one.

Progression of hanging two 800amp meter stacks with 8 meter sockets space each. This is for a 14 unit apartment. Lots of...
10/04/2025

Progression of hanging two 800amp meter stacks with 8 meter sockets space each. This is for a 14 unit apartment. Lots of planning and measuring allow us to complete a clean and smooth install.

Retrofit some 65ft pole lights with new LED fixtures and bullhorn. Each fixture puts out 56,000 lumens using less than h...
03/16/2025

Retrofit some 65ft pole lights with new LED fixtures and bullhorn. Each fixture puts out 56,000 lumens using less than half the energy as the old mercury v***r bulbs.

This customer had old distribution panels that were installed in the 1960’s. Breakers were starting to go bad and they d...
12/21/2024

This customer had old distribution panels that were installed in the 1960’s. Breakers were starting to go bad and they do not manufacture new breakers to fit this distribution anymore.

We ordered two new 400 amp distributions for this customer. The challenge here is the new distributions are more compact than the old. This lead us to get creative in getting the existing conduits into the new distributions. After lots of planning and prepping this is what we came up with.

The 2024 code also required us to add 400 amp emergency disconnects on the exterior of the building for each distribution.

Progression on a 400 amp feed through panel install. This takes planning from pre-slab unground work to completion -Brin...
10/19/2024

Progression on a 400 amp feed through panel install.

This takes planning from pre-slab unground work to completion
-Bringing conduits up in exact locations
-Knocking out holes in metal gutters and panelboards allowing for holes to line up perfectly.
-Cutting conduits to exact lengths allowing cans to be plumb and level

This manufactured home had its electrical service on a rotted wood post that was 1 foot off the ground. It was also powe...
08/09/2024

This manufactured home had its electrical service on a rotted wood post that was 1 foot off the ground. It was also powering the home with a heavy duty cord on the ground.

We came in and raised the meter socket up to a code acceptable height. Mounted it on a 4x4 steel post and ran conduit to the home. This service is safer and will have more longevity.

Ran some conduit out of the block storm shelter walls. These conduits will be under the cement slab floor and they will ...
07/20/2024

Ran some conduit out of the block storm shelter walls. These conduits will be under the cement slab floor and they will pop up into some walls that will be framed out by the framers.

Laid two 3” conduits in the ground to bring power to a 600 amp meter stack to power a cell tower around Humphrey. Also p...
07/02/2024

Laid two 3” conduits in the ground to bring power to a 600 amp meter stack to power a cell tower around Humphrey.

Also provided two 4” conduits to under ground data boxes.

New addition going in on this home. Existing 100 amp panel was too small for the new loads being added. We dug up the ex...
05/18/2024

New addition going in on this home. Existing 100 amp panel was too small for the new loads being added. We dug up the existing wires, spliced them with a UL listed underground waterproof splice, and ran them through and existing basement ceiling to feed the new 200 amp panel. We then sub fed the existing panel off of the new 200 amp panel to power the existing circuits in the home. We made straight cuts in the drywall along the floor joist to keep the repair easy for the the drywallers.

Trenched in power for some duplexes going up in David City. Meter socket was installed at the back of the lot by the cit...
05/11/2024

Trenched in power for some duplexes going up in David City. Meter socket was installed at the back of the lot by the city. This allowed us to run direct bury cable to the home and transition over to conduit when entering the home. Conduit is necessary due to it being under the concrete slab. Stubbed up the conduit in the garage right where the panel will go.

Built this 12’ wide by 10’ stand for a 1000 amp service. We used 16’ 4x4 steel post painted black, sunk them 6’ into the...
03/09/2024

Built this 12’ wide by 10’ stand for a 1000 amp service. We used 16’ 4x4 steel post painted black, sunk them 6’ into the ground, and concreted into the ground.

The interiors of this distribution center have been on back order for over 10 months. We came up with a temporary solution to power it up. Allowing the customer to open up the RV park.

No outlets in this backsplash. We used an angled plug mold on the bottom of the upper cabinets to give this kitchen that...
03/02/2024

No outlets in this backsplash. We used an angled plug mold on the bottom of the upper cabinets to give this kitchen that modern look.

Address

702 Pine Street
Humphrey, NE
68642

Telephone

+14029201730

Website

Alerts

Be the first to know and let us send you an email when Top Notch Electric, LLC posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category