12/27/2025
TOP-O-TEXAS POWER TOOL & WATER HEATER SHOP IN LELIA LAKE, TX 79240 Has Reconditioned Gas & Electric Residential Water Heaters For Sale "WITH A WARRANTY" or I can recondition yours if it's not leaking!! I also have Gas Valves, Burner Assemblies, Pilot Parts, T&P Valves, Dielectric Ni***es, Sacrificial Anode Rods, Dip Tubes, Flexible Water & Gas Line Connectors, Heating Elements, Leak Pans and More.
I repair & sell Parts for Pressure Washers & Air Compressors plus I have rebuilt units in stock for sale.
I OFFER FREE DELIVERY ON RECONDITIONED WATER HEATERS UP TO 75 MILES AWAY. ADD $1.00 MILE OVER 75 MILES 1-WAY.
Our Water Heaters Are Reconditioned by Me, Roddy Klinnert, A Texas State Licensed Master Plumber With 60 Years of Water Heater Troubleshooting & Repair Experience.
What does "RECONDITIONING" a water consist of?? See my 12-step process below so you know what you're getting with our Reconditioned water heaters!!
1: It's stripped of the controls & heating devices
2: It's placed in the test pit and filled with water to 90% full then topped off with air to 140 PSI for a 24-36 hour pressure test to determine if the tank is solid and make sure it does not leak. Most cities water pressure is 50-70 PSI therefore I pressure test each tank at double that, 140 PSI for your safety and a long term tank life span..
3: If it fails the 140 # test, it goes to a scrap pile!!
4: If it passes the 140 # test, the tank is flushed with a 2000 PSI pressure washer using a special "high speed rotating turbo tip" inserted through the Anode Rod opening at the top of the water heater tank to break up & flush out any sediment & calcium deposits giving us a clean, pressure tested water tank to work with.
5: All of the pipe threads where control devices are installed are cleaned, inspected & re-tapped to assure that all controls & safety devices are properly fitted & sealed tight with Teflon Tape assuring there are no water leaks when installed.
6: A new Anode Rod & 2-new Dielectric ni***es are installed on the top side using Teflon Tape as a sealant & tightened to proper torque using a "preset trip setting" Torque Wrench.
7: The water heater is then laid down horizontally on a table & the bottom removed to clean & inspect the combustion air metal intake filters on gas water heaters, then clean the burner chamber and also remove any major dents in the lower outer skin of the water heater and reinstall the bottom using new hex head self tapping screws.
8A: Gas water heaters get the control valve and the complete burner assembly cleaned & bench tested for function as well as accuracy and repaired if needed prior to installation back in the water heater burner chamber. The control valve and burner assembly are then re-tested again to insure correct operational function in your home.
8B: Electric water heaters automatically get both heating elements replaced with new heating elements even if the old ones are still working and the internal electrical wiring checked for insulation safety. Both the upper & lower water temperature thermostats are tested for function and tight seating against the water tank and are replaced if needed.
9: A new brass drain valve is installed in place of the cheap plastic drain valve that never worked.
10: A new T&P (Temperature & Pressure) safety relief valve is installed for safety purposes.
11: The water heater outer skin is cleaned as best we can with a special proprietary solution.
12. All model and serial number identifying information plus individual specifications are recorded on the shop reconditioning work order and then recorded in our computer system with our individual 4-digit Identification number added to the water heater outer skin with a magic marker for tracking and warranty purposes allowing me to know exactly what water heater you have and how it's equipped in case you need me to troubleshoot it on the phone later on down the road. The buyer (your) name and our Identification number is added to that data base once the water heater is purchased by you.
This 12-step process listed above takes about 3-days start to finish as I want to make sure each water heater is as good as it can possibly be for your safety and to give you a long period of reliable, trouble free water heater service!!
I also stock & will ship to you if ever needed, hard to find repair parts for most brands of residential water heaters. If your water heater quits working & it's not leaking, it can usually be repaired saving you considerable cost over replacing it. Before you replace it, call me to see if I can help you troubleshoot it over the phone & send you the right parts!!
Yes it's a bit of a different concept however it has worked for many years & saved a lot of folks a lot of money. I've even had some ladies that have fixed their failed water heater this way.
Roddy Klinnert DBA
Top-O-Texas Power Tool / Water Heater Shop
4195-B FM 1754
Lelia Lake, TX 79240
Email: [email protected]
Office: 806-494-5000
Hours: 8-12 & 1-5, Monday-Friday (however I usually answer the phone anytime it rings unless I'm in a meeting, in the shower or in Church)
I accept Cash, local checks, bank wire transfers, MasterCard, Visa, Discover & American Express credit & debit cards. I DO NOT ACCEPT ANY CASH APP TRANSACTIONS (sorry but I've already been ripped off twice by those gibberish talking Cash App foreign crooks).